In the non highmem case, if two memory banks of 1GB each are provided,
the second bank would evade suppression since its virtual base would
be 0. Fix this by disallowing any memory bank which virtual base
address is found to be lower than PAGE_OFFSET.
Reported-by: Lennert Buytenhek <[email protected]>
Signed-off-by: Nicolas Pitre <[email protected]>
Signed-off-by: Russell King <[email protected]>
This reverts commit 7e86c0e685 ("do not
overwrite EEPROM on Xonar D2/D2X") because it did not actually help with
the problem.
More user reports show that the overwriting of the EEPROM is not
triggered by using this driver but by installing Linux, and that the
installation of any other operating system (even one without any CMI8788
driver) has the same effect. In other words, the presence of this
driver does not have any effect on the occurrence of the error. (So
far, the available evidence seems to point to a BIOS bug.)
Furthermore, it turns out that the EEPROM chip is protected against
stray write commands by the command format and by requiring a separate
write-enable command, so the error scenario in the previous commit (that
SPI writes can be misinterpreted as an EEPROM write command) is not even
theoretically possible.
The mixer control that was removed as a consequence of the previous
commit can only be partially emulated in userspace, which also means it
cannot be seen be the in-kernel OSS API emulation, so it is better to
revert that change.
Signed-off-by: Clemens Ladisch <[email protected]>
Cc: <[email protected]>
Signed-off-by: Takashi Iwai <[email protected]>
After moving mac addresses in __vlan_put_tag() skb->mac_header needs
to be updated.
Reported-by: Karl Hiramoto <[email protected]>
Signed-off-by: Jarek Poplawski <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
crypto_ahash_show changed to use cra_ahash for digestsize reference.
Signed-off-by: Lee Nipper <[email protected]>
Signed-off-by: Herbert Xu <[email protected]>
Impact: prevent deadlock if ring buffer gets corrupted
This patch adds a paranoid check to make sure the ring buffer consumer
does not go into an infinite loop. Since the ring buffer has been set
to read only, the consumer should not loop for more than the ring buffer
size. A check is added to make sure the consumer does not loop more than
the ring buffer size.
Signed-off-by: Steven Rostedt <[email protected]>
Impact: Move variable declaration as far inner as possible.
Fix this sparse warning:
drivers/net/igb/igb_main.c:1895:21: warning: symbol 'j' shadows an earlier one
drivers/net/igb/igb_main.c:1855:16: originally declared here
Signed-off-by: Hannes Eder <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
During the move of support for PCIe devices from e1000 to e1000e, this
workaround necessary only for older non-PCIe devices was mistakenly
copied into e1000e. Remove it.
Signed-off-by: Jesse Brandeburg <[email protected]>
Acked-by: Bruce Allan <[email protected]>
Signed-off-by: Jeff Kirsher <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
Impact: fix output of function tracer to be useful
The function tracer is pretty useless if KALLSYMS is not configured.
Unless you are good at reading hex values, the function tracer should
select the KALLSYMS configuration.
Also, the dynamic function tracer will fail its self test if KALLSYMS
is not selected.
Signed-off-by: Steven Rostedt <[email protected]>
Impact: fix to prevent hard lockup on self tests
If one of the tracers are broken and is constantly filling the ring
buffer while the test of the ring buffer is running, it will hang
the box. The reason is that the test is a consumer that will not
stop till the ring buffer is empty. But if the tracer is broken and
is constantly producing input to the buffer, this test will never
end. The result is a lockup of the box.
This happened when KALLSYMS was not defined and the dynamic ftrace
test constantly filled the ring buffer, because the filter failed
and all functions were being traced. Something was being called
that constantly filled the buffer.
Signed-off-by: Steven Rostedt <[email protected]>
* 'for-linus' of git://git.kernel.dk/linux-2.6-block:
block: fix deadlock in blk_abort_queue() for drivers that readd to timeout list
block: fix booting from partitioned md array
block: revert part of 18ce3751cc
cciss: PCI power management reset for kexec
paride/pg.c: xs(): &&/|| confusion
fs/bio: bio_alloc_bioset: pass right object ptr to mempool_free
block: fix bad definition of BIO_RW_SYNC
bsg: Fix sense buffer bug in SG_IO
To match ixgbe GRO functionality, we remove the LRO (which is now GRO)
Kconfig option which enables GRO by default.
Signed-off-by: Jeff Kirsher <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/drzeus/mmc:
omap_hsmmc: Change while(); loops with finite version
omap_hsmmc: recover from transfer failures
omap_hsmmc: only MMC1 allows HCTL.SDVS != 1.8V
omap_hsmmc: card detect irq bugfix
sdhci: fix led naming
mmc_test: fix basic read test
s3cmci: Fix hangup in do_pio_write()
Revert "sdhci: force high speed capability on some controllers"
MMC: fix bug - SDHC card capacity not correct
Optimize skb_tx_hash() by eliminating a comparison that executes for
every packet. skb_tx_hashrnd initialization is moved to a later part of
the startup sequence, namely after the "random" driver is initialized.
Rebooted the system three times and verified that the code generates
different random numbers each time.
Signed-off-by: Krishna Kumar <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
Introduced support for link speed and duplex setting (ethtool -s),
link advertising parameters and autonegotiation (ethtool -r):
- struct niu_link_config: split advertising and autoneg
fields into active and target values (similar to speed
and duplex fields)
- mii_init_common(): rewrite function to actually apply
requested niu_link_config parameters instead of providing
default initialization
- link_status_1g(): move parsing of MII registers into
new link_status_mii() function (link_status_1g_rgmii()
could possibly use this new implementation too)
- introduce simple nway_reset method
- fix incorrect XMAC_CONFIG_MODE selection for 10Mbps case
Signed-off-by: Constantin Baranov <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
Fixed a typo in niu_determine_phy_disposition() which resulted in
phy_template_1g_copper being selected for 10G/copper configuration.
Signed-off-by: Constantin Baranov <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
Impact: Include the header file. If CONFIG_SFC_MTD is not defined
then the functions 'efx_mtd_remove' and 'efx_mtd_rename' are defined
'static inline' with an empty function body in the header file, but
the the whole file mtd.c is not built in this case.
Fix this sparse warnings:
drivers/net/sfc/mtd.c:204:6: warning: symbol 'efx_mtd_remove' was not declared. Should it be static?
drivers/net/sfc/mtd.c:221:6: warning: symbol 'efx_mtd_rename' was not declared. Should it be static?
drivers/net/sfc/mtd.c:230:5: warning: symbol 'efx_mtd_probe' was not declared. Should it be static?
Signed-off-by: Hannes Eder <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
Add support for adapters with a PCI id equal to 0x35.
Signed-off-by: Divy Le Ray <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
phyid Can't be both TG3_PHY_OUI_1 and TG3_PHY_OUI_2 and TG3_PHY_OUI_3.
Signed-off-by: Roel Kluin <[email protected]>
Acked-by: Matt Carlson <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
mib_counters_update() also restarts the timer.
So the timer is dequeued, the stats are read and then the timer is
enqueued again. This is "okay" unless someone unloads the module.
The locking here is also broken:
mib_counters_update() grabs just a simple spinlock. The only thing the
lock is good for is to protect the timer func against other callers
namely mv643xx_eth_stop() && mv643xx_eth_get_ethtool_stats(). That means
if the spinlock is taken via the ethtool path and than the timer kicks
in then the box will lock up.
Signed-off-by: Sebastian Andrzej Siewior <[email protected]>
Acked-by: Lennert Buytenhek <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
gpio_get_value() returns 0 or nonzero, but getmiso() expects 0 or 1.
Sanitize the value to a 0/1 boolean.
Signed-off-by: Michael Buesch <[email protected]>
Acked-by: David Brownell <[email protected]>
Signed-off-by: Andrew Morton <[email protected]>
Signed-off-by: Linus Torvalds <[email protected]>
Build breaks when DELL_LAPTOP=y and POWER_SUPPLY=m. DELL_LAPTOP needs to
depend on POWER_SUPPLY.
dell-laptop.c:(.text+0x1ef3c4): undefined reference to `power_supply_is_system_supplied'
dell-laptop.c:(.text+0x1ef45e): undefined reference to `power_supply_is_system_supplied'
Signed-off-by: Randy Dunlap <[email protected]>
Cc: Matthew Garrett <[email protected]>
Cc: Ingo Molnar <[email protected]>
Cc: Thomas Gleixner <[email protected]>
Cc: "H. Peter Anvin" <[email protected]>
Cc: Len Brown <[email protected]>
Signed-off-by: Andrew Morton <[email protected]>
Signed-off-by: Linus Torvalds <[email protected]>
Submenus of the graphics support "Support for frame buffer devices" and
"Direct Rendering Manager (XFree86 4.1.0 and higher DRI support)" are
broken in half after latest changes for Intel 915 mode setting support.
The DRM subsection is broken because one option is put outside the choice
section it depends on.
The frame buffers part is broken then due to circular dependency. Fix
this by make Intel frame buffers depend on CONFIG_INTEL_AGP.
Kconfigs are broken by d2f5935770
("drm/i915: select framebuffer support automatically").
This is probably not only way to fix this.
Signed-off-by: Krzysztof Helt <[email protected]>
Cc: Ingo Molnar <[email protected]>
Cc: Dave Airlie <[email protected]>
Signed-off-by: Andrew Morton <[email protected]>
Signed-off-by: Linus Torvalds <[email protected]>
The floppy driver requests an I/O port it doesn't need, and sometimes this
causes a conflict with a motherboard device reported by PNPBIOS.
This patch makes the floppy driver request and release only the ports it
actually uses. It also factors out the request/release stuff and the
io-ports list so they're all in one place now.
The current floppy driver uses only these ports:
0x3f2 (FD_DOR)
0x3f4 (FD_STATUS)
0x3f5 (FD_DATA)
0x3f7 (FD_DCR/FD_DIR)
but it requests 0x3f2-0x3f5 and 0x3f7, which includes the unused port
0x3f3.
Some BIOSes report 0x3f3 as a motherboard resource. The PNP system driver
reserves that, which causes a conflict when the floppy driver requests
0x3f2-0x3f5 later.
Philippe reported that this conflict broke the floppy driver between
2.6.11 and 2.6.22. His PNPBIOS reports these devices:
$ cat 00:07/id 00:07/resources # motherboard device
PNP0c02
state = active
io 0x80-0x80
io 0x10-0x1f
io 0x22-0x3f
io 0x44-0x5f
io 0x90-0x9f
io 0xa2-0xbf
io 0x3f0-0x3f1
io 0x3f3-0x3f3
$ cat 00:03/id 00:03/resources # floppy device
PNP0700
state = active
io 0x3f4-0x3f5
io 0x3f2-0x3f2
Reference:
http://lkml.org/lkml/2009/1/31/162
Signed-off-by: Bjorn Helgaas <[email protected]>
Signed-off-by: Philippe De Muyter <[email protected]>
Reported-by: Philippe De Muyter <[email protected]>
Tested-by: Philippe De Muyter <[email protected]>
Cc: Adam M Belay <[email protected]>
Cc: Robert Hancock <[email protected]>
Signed-off-by: Andrew Morton <[email protected]>
Signed-off-by: Linus Torvalds <[email protected]>
I have a Digi Neo 8 PCI card (114f:00b1) Serial controller: Digi
International Digi Neo 8 (rev 05)
that works with the jsm driver after using the following patch.
Signed-off-by: Adam Lackorzynski <[email protected]>
Cc: Scott H Kilau <[email protected]>
Cc: Wendy Xiong <[email protected]>
Acked-by: Alan Cox <[email protected]>
Signed-off-by: Andrew Morton <[email protected]>
Signed-off-by: Linus Torvalds <[email protected]>
Now, early_pfn_in_nid(PFN, NID) may returns false if PFN is a hole.
and memmap initialization was not done. This was a trouble for
sparc boot.
To fix this, the PFN should be initialized and marked as PG_reserved.
This patch changes early_pfn_in_nid() return true if PFN is a hole.
Signed-off-by: KAMEZAWA Hiroyuki <[email protected]>
Reported-by: David Miller <[email protected]>
Tested-by: KOSAKI Motohiro <[email protected]>
Cc: Mel Gorman <[email protected]>
Cc: Heiko Carstens <[email protected]>
Cc: <[email protected]> [2.6.25.x, 2.6.26.x, 2.6.27.x, 2.6.28.x]
Signed-off-by: Andrew Morton <[email protected]>
Signed-off-by: Linus Torvalds <[email protected]>
What's happening is that the assertion in mm/page_alloc.c:move_freepages()
is triggering:
BUG_ON(page_zone(start_page) != page_zone(end_page));
Once I knew this is what was happening, I added some annotations:
if (unlikely(page_zone(start_page) != page_zone(end_page))) {
printk(KERN_ERR "move_freepages: Bogus zones: "
"start_page[%p] end_page[%p] zone[%p]\n",
start_page, end_page, zone);
printk(KERN_ERR "move_freepages: "
"start_zone[%p] end_zone[%p]\n",
page_zone(start_page), page_zone(end_page));
printk(KERN_ERR "move_freepages: "
"start_pfn[0x%lx] end_pfn[0x%lx]\n",
page_to_pfn(start_page), page_to_pfn(end_page));
printk(KERN_ERR "move_freepages: "
"start_nid[%d] end_nid[%d]\n",
page_to_nid(start_page), page_to_nid(end_page));
...
And here's what I got:
move_freepages: Bogus zones: start_page[2207d0000] end_page[2207dffc0] zone[fffff8103effcb00]
move_freepages: start_zone[fffff8103effcb00] end_zone[fffff8003fffeb00]
move_freepages: start_pfn[0x81f600] end_pfn[0x81f7ff]
move_freepages: start_nid[1] end_nid[0]
My memory layout on this box is:
[ 0.000000] Zone PFN ranges:
[ 0.000000] Normal 0x00000000 -> 0x0081ff5d
[ 0.000000] Movable zone start PFN for each node
[ 0.000000] early_node_map[8] active PFN ranges
[ 0.000000] 0: 0x00000000 -> 0x00020000
[ 0.000000] 1: 0x00800000 -> 0x0081f7ff
[ 0.000000] 1: 0x0081f800 -> 0x0081fe50
[ 0.000000] 1: 0x0081fed1 -> 0x0081fed8
[ 0.000000] 1: 0x0081feda -> 0x0081fedb
[ 0.000000] 1: 0x0081fedd -> 0x0081fee5
[ 0.000000] 1: 0x0081fee7 -> 0x0081ff51
[ 0.000000] 1: 0x0081ff59 -> 0x0081ff5d
So it's a block move in that 0x81f600-->0x81f7ff region which triggers
the problem.
This patch:
Declaration of early_pfn_to_nid() is scattered over per-arch include
files, and it seems it's complicated to know when the declaration is used.
I think it makes fix-for-memmap-init not easy.
This patch moves all declaration to include/linux/mm.h
After this,
if !CONFIG_NODES_POPULATES_NODE_MAP && !CONFIG_HAVE_ARCH_EARLY_PFN_TO_NID
-> Use static definition in include/linux/mm.h
else if !CONFIG_HAVE_ARCH_EARLY_PFN_TO_NID
-> Use generic definition in mm/page_alloc.c
else
-> per-arch back end function will be called.
Signed-off-by: KAMEZAWA Hiroyuki <[email protected]>
Tested-by: KOSAKI Motohiro <[email protected]>
Reported-by: David Miller <[email protected]>
Cc: Mel Gorman <[email protected]>
Cc: Heiko Carstens <[email protected]>
Cc: <[email protected]> [2.6.25.x, 2.6.26.x, 2.6.27.x, 2.6.28.x]
Signed-off-by: Andrew Morton <[email protected]>
Signed-off-by: Linus Torvalds <[email protected]>
Li Zefan said:
Thread 1:
for ((; ;))
{
mount -t cpuset xxx /mnt > /dev/null 2>&1
cat /mnt/cpus > /dev/null 2>&1
umount /mnt > /dev/null 2>&1
}
Thread 2:
for ((; ;))
{
mount -t cpuset xxx /mnt > /dev/null 2>&1
umount /mnt > /dev/null 2>&1
}
(Note: It is irrelevant which cgroup subsys is used.)
After a while a lockdep warning showed up:
=============================================
[ INFO: possible recursive locking detected ]
2.6.28 #479
---------------------------------------------
mount/13554 is trying to acquire lock:
(&type->s_umount_key#19){--..}, at: [<c049d888>] sget+0x5e/0x321
but task is already holding lock:
(&type->s_umount_key#19){--..}, at: [<c049da0c>] sget+0x1e2/0x321
other info that might help us debug this:
1 lock held by mount/13554:
#0: (&type->s_umount_key#19){--..}, at: [<c049da0c>] sget+0x1e2/0x321
stack backtrace:
Pid: 13554, comm: mount Not tainted 2.6.28-mc #479
Call Trace:
[<c044ad2e>] validate_chain+0x4c6/0xbbd
[<c044ba9b>] __lock_acquire+0x676/0x700
[<c044bb82>] lock_acquire+0x5d/0x7a
[<c049d888>] ? sget+0x5e/0x321
[<c061b9b8>] down_write+0x34/0x50
[<c049d888>] ? sget+0x5e/0x321
[<c049d888>] sget+0x5e/0x321
[<c045a2e7>] ? cgroup_set_super+0x0/0x3e
[<c045959f>] ? cgroup_test_super+0x0/0x2f
[<c045bcea>] cgroup_get_sb+0x98/0x2e7
[<c045cfb6>] cpuset_get_sb+0x4a/0x5f
[<c049dfa4>] vfs_kern_mount+0x40/0x7b
[<c049e02d>] do_kern_mount+0x37/0xbf
[<c04af4a0>] do_mount+0x5c3/0x61a
[<c04addd2>] ? copy_mount_options+0x2c/0x111
[<c04af560>] sys_mount+0x69/0xa0
[<c0403251>] sysenter_do_call+0x12/0x31
The cause is after alloc_super() and then retry, an old entry in list
fs_supers is found, so grab_super(old) is called, but both functions hold
s_umount lock:
struct super_block *sget(...)
{
...
retry:
spin_lock(&sb_lock);
if (test) {
list_for_each_entry(old, &type->fs_supers, s_instances) {
if (!test(old, data))
continue;
if (!grab_super(old)) <--- 2nd: down_write(&old->s_umount);
goto retry;
if (s)
destroy_super(s);
return old;
}
}
if (!s) {
spin_unlock(&sb_lock);
s = alloc_super(type); <--- 1th: down_write(&s->s_umount)
if (!s)
return ERR_PTR(-ENOMEM);
goto retry;
}
...
}
It seems like a false positive, and seems like VFS but not cgroup needs to
be fixed.
Peter said:
We can simply put the new s_umount instance in a but lockdep doesn't
particularly cares about subclass order.
If there's any issue with the callers of sget() assuming the s_umount lock
being of sublcass 0, then there is another annotation we can use to fix
that, but lets not bother with that if this is sufficient.
Addresses http://bugzilla.kernel.org/show_bug.cgi?id=12673
Signed-off-by: Peter Zijlstra <[email protected]>
Tested-by: Li Zefan <[email protected]>
Reported-by: Li Zefan <[email protected]>
Cc: Al Viro <[email protected]>
Cc: Paul Menage <[email protected]>
Cc: Arjan van de Ven <[email protected]>
Signed-off-by: Andrew Morton <[email protected]>
Signed-off-by: Linus Torvalds <[email protected]>
I found a problem of handling of modem status of atmel_serial driver.
With the commit 1ecc26 ("atmel_serial: split the interrupt handler"),
handling of modem status signal was splitted into two parts. The
atmel_tasklet_func() compares new status with irq_status_prev, but
irq_status_prev is not correct if signal status was changed while the port
is closed.
Here is a sequence to cause problem:
1. Remote side sets CTS (and DSR).
2. Local side close the port.
3. Local side clears RTS and DTR.
4. Remote side clears CTS and DSR.
5. Local side reopen the port. hw_stopped becomes 1.
6. Local side sets RTS and DTR.
7. Remote side sets CTS and DSR.
Then CTS change interrupt can be received, but since CTS bit in
irq_status_prev and new status is same, uart_handle_cts_change() will not
be called (so hw_stopped will not be cleared, i.e. cannot send any data).
I suppose irq_status_prev should be initialized at somewhere in open
sequence.
Itai Levi pointed out that we need to initialize atmel_port->irq_status
as well here. His analysis is as follows:
> Regarding the second part of the patch (which resets irq_status_prev),
> it turns out that both versions of the patch (mine and Atsushi's)
> still leave enough room for faulty behavior when opening the port.
>
> This is because we are not resetting both irq_status_prev and
> irq_status in atmel_startup() to CSR, which leads faulty behavior in
> the following sequences:
>
> First case:
> 1. closing the port while CTS line = 1 (TX not allowed)
> 2. setting CTS line = 0 (TX allowed)
> 3. opening the port
> 4. transmitting one char
> 5. Cannot transmit more chars, although CTS line is 0
>
> Second case:
> 1. closing the port while CTS line = 0 (TX allowed)
> 2. setting CTS line = 1 (TX not allowed)
> 3. opening the port
> 4. receiving some chars
> 5. Now we can transmit, although CTS line is 1
>
> This reason for this is that the tasklet is scheduled as a result of
> TX or RX interrupts (not a status change!), in steps 4 above. Inside
> the tasklet, the atmel_port->irq_status (which holds the value from
> the previous session) is compared to atmel_port->irq_status_prev.
> Hence, a status-change of the CTS line is faultily detected.
>
> Both cases were verified on 9260 hardware.
[[email protected]: folded with patch from Itai Levi]
Signed-off-by: Atsushi Nemoto <[email protected]>
Signed-off-by: Haavard Skinnemoen <[email protected]>
Cc: Remy Bohmer <[email protected]>
Cc: Marc Pignat <[email protected]>
Cc: Itai Levi <[email protected]>
Cc: Alan Cox <[email protected]>
Signed-off-by: Andrew Morton <[email protected]>
Signed-off-by: Linus Torvalds <[email protected]>
The conversion of atmel-mci to dma_request_channel missed the
initialization of the channel dma_slave information. The filter_fn passed
to dma_request_channel is responsible for initializing the channel's
private data. This implementation has the additional benefit of enabling
a generic client-channel data passing mechanism.
Reviewed-by: Atsushi Nemoto <[email protected]>
Signed-off-by: Dan Williams <[email protected]>
Acked-by: Haavard Skinnemoen <[email protected]>
Signed-off-by: Andrew Morton <[email protected]>
Signed-off-by: Linus Torvalds <[email protected]>
Add support for HP Pavilion dv5.
Since Intel-based models have an inverted x axis, while AMD-based models
have an inverted y axis, we introduce a new macro that special-cases axis
orientation based on two DMI entries: HP dv5 axis configuration is then
based on both the PRODUCT and BOARD name.
Signed-off-by: Giuseppe Bilotta <[email protected]>
Cc: Eric Piel <[email protected]>
Cc: Pavel Machek <[email protected]>
Tested-by: Palatis Tseng <[email protected]>
Signed-off-by: Andrew Morton <[email protected]>
Signed-off-by: Linus Torvalds <[email protected]>
Sensors responding with 0x3B to WHO_AM_I only have one data register per
direction, thus returning a signed byte from the position which is
occupied by the MSB in sensors responding with 0x3A.
Since multiple sensors share the reply to WHO_AM_I, we rename the defines
to better indicate what they identify (family of single and double
precision sensors).
We support both kind of sensors by checking for the sensor type on init
and defining appropriate data-access routines and sensor limits (for the
joystick) depending on what we find.
[[email protected]: coding-style fixes]
Signed-off-by: Giuseppe Bilotta <[email protected]>
Acked-by: Eric Piel <[email protected]>
Cc: Pavel Machek <[email protected]>
Signed-off-by: Andrew Morton <[email protected]>
Signed-off-by: Linus Torvalds <[email protected]>
This adds freefall handling to hp_accel driver. According to HP, it
should just work, without us having to set the chip up by hand.
hpfall.c is example .c program that parks the disk when accelerometer
detects free fall. It should work; for now, it uses fixed 20seconds
protection period.
Signed-off-by: Pavel Machek <[email protected]>
Cc: Thomas Renninger <[email protected]>
Cc: Éric Piel <[email protected]>
Signed-off-by: Andrew Morton <[email protected]>
Signed-off-by: Linus Torvalds <[email protected]>
Otherwise with INPUT=m, EEEPC_LAPTOP=y one gets
drivers/built-in.o: In function `input_sync':
eeepc-laptop.c:(.text+0x18ce51): undefined reference to `input_event'
drivers/built-in.o: In function `input_report_key':
eeepc-laptop.c:(.text+0x18ce73): undefined reference to `input_event'
drivers/built-in.o: In function `eeepc_hotk_check':
eeepc-laptop.c:(.text+0x18d05f): undefined reference to `input_allocate_device'
eeepc-laptop.c:(.text+0x18d10f): undefined reference to `input_register_device'
eeepc-laptop.c:(.text+0x18d131): undefined reference to `input_free_device'
drivers/built-in.o: In function `eeepc_backlight_exit':
eeepc-laptop.c:(.text+0x18d546): undefined reference to `input_unregister_device'
Signed-off-by: Alexey Dobriyan <[email protected]>
Cc: Len Brown <[email protected]>
Cc: Ingo Molnar <[email protected]>
Signed-off-by: Andrew Morton <[email protected]>
Signed-off-by: Linus Torvalds <[email protected]>
In cgroup_kill_sb(), root is freed before sb is detached from the list, so
another sget() may find this sb and call cgroup_test_super(), which will
access the root that has been freed.
Reported-by: Al Viro <[email protected]>
Signed-off-by: Li Zefan <[email protected]>
Acked-by: Paul Menage <[email protected]>
Signed-off-by: Andrew Morton <[email protected]>
Signed-off-by: Linus Torvalds <[email protected]>
YAMAMOTO-san noticed that task_dirty_inc doesn't seem to be called properly for
cases where set_page_dirty is not used to dirty a page (eg. mark_buffer_dirty).
Additionally, there is some inconsistency about when task_dirty_inc is
called. It is used for dirty balancing, however it even gets called for
__set_page_dirty_no_writeback.
So rather than increment it in a set_page_dirty wrapper, move it down to
exactly where the dirty page accounting stats are incremented.
Cc: YAMAMOTO Takashi <[email protected]>
Signed-off-by: Nick Piggin <[email protected]>
Acked-by: Peter Zijlstra <[email protected]>
Signed-off-by: Andrew Morton <[email protected]>
Signed-off-by: Linus Torvalds <[email protected]>
As requested by Michael, add a missing check for valid flags in
timerfd_settime(), and make it return EINVAL in case some extra bits are
set.
Michael said:
If this is to be any use to userland apps that want to check flag
support (perhaps it is too late already), then the sooner we get it
into the kernel the better: 2.6.29 would be good; earlier stables as
well would be even better.
[[email protected]: remove unused TFD_FLAGS_SET]
Acked-by: Michael Kerrisk <[email protected]>
Signed-off-by: Davide Libenzi <[email protected]>
Cc: <[email protected]> [2.6.27.x, 2.6.28.x]
Signed-off-by: Andrew Morton <[email protected]>
Signed-off-by: Linus Torvalds <[email protected]>
My @suse.cz address will stop working some day, so put working one into
MAINTAINERS/CREDITS. It would be cool to get this to 2.6.29... it should
not really break anything.
Signed-off-by: Pavel Machek <[email protected]>
Cc: Jiri Kosina <[email protected]>
Signed-off-by: Andrew Morton <[email protected]>
Signed-off-by: Linus Torvalds <[email protected]>
Currently seq_read assumes that the offset passed to it is always the
offset it passed to user space. In the case pread this assumption is
broken and we do the wrong thing when presented with pread.
To solve this I introduce an offset cache inside of struct seq_file so we
know where our logical file position is. Then in seq_read if we try to
read from another offset we reset our data structures and attempt to go to
the offset user space wanted.
[[email protected]: restore FMODE_PWRITE]
[[email protected]: seq_open needs its fmode opened up to take advantage of this]
Signed-off-by: Eric Biederman <[email protected]>
Cc: Alexey Dobriyan <[email protected]>
Cc: Al Viro <[email protected]>
Cc: Paul Turner <[email protected]>
Cc: <[email protected]> [2.6.25.x, 2.6.26.x, 2.6.27.x, 2.6.28.x]
Signed-off-by: Andrew Morton <[email protected]>
Signed-off-by: Linus Torvalds <[email protected]>
Separate FMODE_PREAD and FMODE_PWRITE into separate flags to reflect the
reality that the read and write paths may have independent restrictions.
A git grep verifies that these flags are always cleared together so this
new behavior will only apply to interfaces that change to clear flags
individually.
This is required for "seq_file: properly cope with pread", a post-2.6.25
regression fix.
[[email protected]: add comment]
Signed-off-by: Paul Turner <[email protected]>
Cc: Eric Biederman <[email protected]>
Cc: Alexey Dobriyan <[email protected]>
Cc: Al Viro <[email protected]>
Cc: <[email protected]> [2.6.25.x, 2.6.26.x, 2.6.27.x, 2.6.28.x]
Signed-off-by: Andrew Morton <[email protected]>
Signed-off-by: Linus Torvalds <[email protected]>
Roel Kluin