Allocate memory at the end of sof_ipc_stream_params to store
snd_compr_params in order to be sent them to SOF firmware.
This will help firmware correctly configure codecs parameters.
Notice, that we use 2 bytes from the reserved pool in order to store
the extended data length. This is compatible with older FWs where
there was no extended data.
Signed-off-by: Daniel Baluta <[email protected]>
Reviewed-by: Pierre-Louis Bossart <[email protected]>
Reviewed-by: Ranjani Sridharan <[email protected]>
Reviewed-by: Péter Ujfalusi <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Mark Brown <[email protected]>
IPC4 uses the SET_DX message to enable/disable cores managed by the DSP.
The dx_state.core_mask indicates which core is going to change state,
the dx_state.dx_mask is to power on (1) or off (0) the core.
In the dx_mask only those bits (cores) checked which bit is set in the
core_mask, other bits (cores) ignored.
Signed-off-by: Peter Ujfalusi <[email protected]>
Reviewed-by: Ranjani Sridharan <[email protected]>
Reviewed-by: Bard Liao <[email protected]>
Reviewed-by: Pierre-Louis Bossart <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Mark Brown <[email protected]>
The host stream position is updated when no_stream_position is set as 0.
However current implementation updates host stream position only when
report data is larger than or equal to host period size which is decided
by the period size of host side. It maybe cause host stream position
update not in time. Therefore this patch introduces another field
"cont_update_posn", a boolean value aimed to update host stream position
continuously and based on period size of pipeline. It can get better
precise when need to update host stream position from firmware.
Reviewed-by: Daniel Baluta <[email protected]>
Reviewed-by: Ranjani Sridharan <[email protected]>
Reviewed-by: Kai Vehmanen <[email protected]>
Signed-off-by: YC Hung <[email protected]>
Signed-off-by: Pierre-Louis Bossart <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Mark Brown <[email protected]>
Pull flexible-array transformations from Gustavo Silva:
"Treewide patch that replaces zero-length arrays with flexible-array
members.
This has been baking in linux-next for a whole development cycle"
* tag 'flexible-array-transformations-5.18-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gustavoars/linux:
treewide: Replace zero-length arrays with flexible-array members
Remove the comp_dai and dai_config members of struct snd_sof_dai and
replace it with a void *private field. Introduce a new struct
sof_dai_private_data that will contain the pointer to these two fields.
The topology parser will populate this structure and save it as part of
the "private" member in snd_sof_dai. Change all users of these fields to
use the private member instead.
Signed-off-by: Ranjani Sridharan <[email protected]>
Reviewed-by: Bard Liao <[email protected]>
Reviewed-by: Péter Ujfalusi <[email protected]>
Reviewed-by: Pierre-Louis Bossart <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Mark Brown <[email protected]>
There is a regular need in the kernel to provide a way to declare
having a dynamically sized set of trailing elements in a structure.
Kernel code should always use “flexible array members”[1] for these
cases. The older style of one-element or zero-length arrays should
no longer be used[2].
This code was transformed with the help of Coccinelle:
(next-20220214$ spatch --jobs $(getconf _NPROCESSORS_ONLN) --sp-file script.cocci --include-headers --dir . > output.patch)
@@
identifier S, member, array;
type T1, T2;
@@
struct S {
...
T1 member;
T2 array[
- 0
];
};
UAPI and wireless changes were intentionally excluded from this patch
and will be sent out separately.
[1] https://en.wikipedia.org/wiki/Flexible_array_member
[2] https://www.kernel.org/doc/html/v5.16/process/deprecated.html#zero-length-and-one-element-arrays
Link: https://github.com/KSPP/linux/issues/78
Reviewed-by: Kees Cook <[email protected]>
Signed-off-by: Gustavo A. R. Silva <[email protected]>
Add a bit definition to the fw_ready message, to denote if the FW
supports the IMR (Isolated Memory Region) restoring feature.
If the bit is set, the driver can skip downloading the firmware again
during system resume or runtime resume.
Bump the ABI version to 3.19 to make it aligned with FW side.
Reviewed-by: Ranjani Sridharan <[email protected]>
Reviewed-by: Péter Ujfalusi <[email protected]>
Signed-off-by: Keyon Jie <[email protected]>
Signed-off-by: Pierre-Louis Bossart <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Mark Brown <[email protected]>
Some DAI components, such as HDaudio, need to be stopped in two steps
a) stop the DAI component
b) stop the DAI DMA
This patch enables this two-step stop by expanding the DAI_CONFIG
IPC flags and split them into 2 parts.
The 4 LSB bits indicate when the DAI_CONFIG IPC is sent, ex: hw_params,
hw_free or pause. The 4 MSB bits are used as the quirk flags to be used
along with the command flags. The quirk flag called
SOF_DAI_CONFIG_FLAGS_2_STEP_STOP shall be set along with the HW_PARAMS
command flag, i.e. before the pipeline is started so that the stop/pause
trigger op in the FW can take the appropriate action to either
perform/skip the DMA stop. If set, the DMA stop will be executed when
the DAI_CONFIG IPC is sent during hw_free. In the case of pause, DMA
pause will be handled when the DAI_CONFIG IPC is sent with the PAUSE
command flag.
Along with this, modify the signature for the hda_ctrl_dai_widget_setup/
hda_ctrl_dai_widget_free() functions to take additional flags as an
argument and modify all users to pass the appropriate quirk flags. Only
the HDA DAI's need to pass the SOF_DAI_CONFIG_FLAGS_2_STEP_STOP quirk
flag during hw_params to indicate that it supports two-step stop and
pause.
Signed-off-by: Ranjani Sridharan <[email protected]>
Reviewed-by: Pierre-Louis Bossart <[email protected]>
Signed-off-by: Kai Vehmanen <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Mark Brown <[email protected]>
Mirror changes done in SOF tree. The changes do not rely on
BIT/GENMASK on purpose to keep the structure and flags common with the
firmware tree.
The DAI_CONFIG IPC is currently used in multiple ways. It is sent to
the DSP firmware when enabling static or dynamic pipelines, in
hw_params or prepare callbacks for Intel SSP, HDaudio and ALH, on
trigger_stop and hw_free.
This IPC has been abused a bit in the past, i.e. the values used for
some of the DAI-specific fields are used to either allocate or free
resources. Two typical examples are Intel HDaudio and SoundWire/ALH
DAIs, where using a zero DMA channel number or stream tag signals to
the firmware the DMA channels or tags allocated earlier can be freed.
Rather than add a new IPC for 'hw_params' and 'hw_free', this patch
suggests supporting a 2-bit value conveying the 'stage' information in
an existing IPC structure. Only 3 possible values are used.
The mapping between HW_PARAMS and HW_FREE flags and ALSA definitions
is not strictly 1:1, e.g. in some cases the HW_PARAM flag might be set
during the .prepare callback, while the HW_FREE might be sent during the
ALSA .trigger for stop/suspend.
The semantics of the flags is to reserve and start/stop all needed
resources, typically hardware related such as DMAs or clocks, when the
HW_PARAMS is set, while the HW_FREE flag allows the firmware to
release the resources allocated. The data transfers are still
controlled within the firmware through the propagation of the trigger
command.
The driver can then pass information that the DAI_CONFIG was invoked
in e.g. a pipeline/DAI setup, hw_params or hw_free stage without
having to use a special DAI-specific encoding. Unfortunately we can't
remove old encodings due to backwards-compatibility requirements but
for new cases, such as the SSP in follow-up patches, we can make the
IPC less cryptic.
This change is tagged as ABI 3.19 and is completely backwards compatible.
Signed-off-by: Pierre-Louis Bossart <[email protected]>
Reviewed-by: Bard Liao <[email protected]>
Reviewed-by: Guennadi Liakhovetski <[email protected]>
Reviewed-by: Brent Lu <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Mark Brown <[email protected]>
The "filter" debugfs file defines the log levels used by
the firmware and reported by sof-logger.
The file contains the formatted entry list, where each entry
follows the following syntax in plain text:
log_level uuid_id pipe_id comp_id;
This file may be updated by userspace applications such sof-logger,
or directly by the user during debugging process.
An unused (wildcard) pipe_id or comp_id value should be set to -1,
uuid_id is hexadecimal value, so when unused then should be set to 0.
When the file is modified, an IPC command is sent to FW with new
trace levels for selected components in filter elements list.
Signed-off-by: Karol Trzcinski <[email protected]>
Reviewed-by: Guennadi Liakhovetski <[email protected]>
Signed-off-by: Kai Vehmanen <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Mark Brown <[email protected]>
Implicit values may have a length of 15bits (s16) so we need to declare
the proper size so we don't get undefined behaviour. This appears to be
arch and compiler dependent. This commit is to keep the headers aligned
between the firmware and kernel. UBSan discovered this bug in the
firmware.
Signed-off-by: Curtis Malainey <[email protected]>
Reviewed-by: Guennadi Liakhovetski <[email protected]>
Signed-off-by: Kai Vehmanen <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Mark Brown <[email protected]>
Use the 32bit reserved member of the struct sof_ipc_comp as the extended
data length, this will help to minimize the ABI change for adding new
extended data to the struct sof_ipc_comp, usually only minor ABI version
bump needed for every update with this new solution.
Signed-off-by: Keyon Jie <[email protected]>
Reviewed-by: Ranjani Sridharan <[email protected]>
Signed-off-by: Kai Vehmanen <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Mark Brown <[email protected]>
This step is needed to add possibility to pack sof_ipc_window inside
another one in used FW build tools - for example in extended manifest.
Structure reusability leads to easy parsing function reuse, so source
code is shorter and easier to maintain.
Using structures with constant size is less tricky and properly
supported by each toolchain by contrast to variable size elements.
This is minor ABI change - backward compatibility is kept.
Signed-off-by: Karol Trzcinski <[email protected]>
Reviewed-by: Guennadi Liakhovetski <[email protected]>
Reviewed-by: Kai Vehmanen <[email protected]>
Reviewed-by: Pierre-Louis Bossart <[email protected]>
Signed-off-by: Ranjani Sridharan <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Mark Brown <[email protected]>
Extended manifest is a place to store build time known firmware
metadata, for example firmware version or used compiler description.
Given information is read on host side before firmware startup.
This part of output binary is located as a first structure in binary
file.
Extended manifest should be skipped in firmware loading routine.
Signed-off-by: Karol Trzcinski <[email protected]>
Signed-off-by: Kai Vehmanen <[email protected]>
Reviewed-by: Guennadi Liakhovetski <[email protected]>
Reviewed-by: Ranjani Sridharan <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Mark Brown <[email protected]>
FW interface for HDA DAI parameters was extended with information on
sampling rate and channel count in version 3.16. Align kernel header
with the FW change. This change is backwards compatible. Old firmware
will ignore the values.
Signed-off-by: Bard Liao <[email protected]>
Signed-off-by: Pierre-Louis Bossart <[email protected]>
Reviewed-by: Guennadi Liakhovetski <[email protected]>
Reviewed-by: Kai Vehmanen <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Mark Brown <[email protected]>
This patch restores the field name to fifo_bits_b since the
legacy firmware compatibility code (for firmware ABI 3.0.0 or earlier)
sets it in sof_link_dmic_load() function in topology.c. Setting of
reserved_2 didn't look appropriate.
Signed-off-by: Seppo Ingalsuo <[email protected]>
Signed-off-by: Pierre-Louis Bossart <[email protected]>
Reviewed-by: Kai Vehmanen <[email protected]>
Reviewed-by: Guennadi Liakhovetski <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Mark Brown <[email protected]>
This patch changes the flexible array member pdm[] into a fixed
array of four that is the max. number of stereo PDM controllers
in the current Intel platforms. The change simplifies DMIC DAI
load code and aligns the IPC with other DAI types.
The change is compatible with old and new firmware with similar
change. The ABI minor version is increased due to change in
IPC headers.
Signed-off-by: Seppo Ingalsuo <[email protected]>
Signed-off-by: Pierre-Louis Bossart <[email protected]>
Reviewed-by: Kai Vehmanen <[email protected]>
Reviewed-by: Guennadi Liakhovetski <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Mark Brown <[email protected]>
Currently if a component source buffer underruns or a component sink
buffer overruns the pipeline will enter an XRUN status and attempt
recovery. This is desired in most pipelines but some topologies need to
support use cases where we expect buffers to underrun or overrun.
Host ---> Proc----> Selector0 --> Buf0 ---- > DAI Playback
|
v
Buf1
|
v
Host <---------------Selector1 <----- Buf2 <----- Echo Ref DAI
In the example above we two host PCMs that can be independently
started/stopped thereby causing buf1 to either underrun or overrun
(and stop the pipelines). Buf1 should be permitted to underrun or overrun
without invoking pipeline XRUN logic and should over write oldest data
(for overrun) and readback 0s (for underrun).
2 flags have been added for use during buffer instantiation:
SOF_BUF_OVERRUN_PERMITTED and SOF_BUF_UNDERRUN_PERMITTED,
along with struct sof_ipc_buffer member fields: flags and reserved.
Flags field is supposed to hold the above-mentioned flags to allow
some control over XRUN behaviour.
Also added reserved field to the structure in case it comes in handy
some time in the future.
This is an incremental ABI change as the new fields are ignored by older
versions of the firmware.
Signed-off-by: Artur Kloniecki <[email protected]>
Signed-off-by: Pierre-Louis Bossart <[email protected]>
Reviewed-by: Kai Vehmanen <[email protected]>
Reviewed-by: Guennadi Liakhovetski <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Mark Brown <[email protected]>
Align struct sof_ipc_cc_version to firmware definition in SOF ABI 3.15.0.
The struct definition was changed due to errors in FW build.
The Cadence XCC compiler produces incorrect linkage section sizes, when a
variable length array is used in the compiler version struct. The firmware
definition was changed to a fixed 32 byte compiler description string.
This length covers all released firmware binaries and thus only a minor
ABI change is needed.
As the same structure is used in IPC messages between driver and firmware,
the kernel needs to be aligned to firmware change.
Signed-off-by: Pan Xiuli <[email protected]>
Signed-off-by: Pierre-Louis Bossart <[email protected]>
Reviewed-by: Kai Vehmanen <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Mark Brown <[email protected]>
Brent Lu