Switch to using the device-managed of_iomap helper to avoid leaking
memory on probe deferral and driver unbind.
Note that this helper checks for already reserved regions and may fail
if there are multiple devices claiming the same memory.
Fixes: e78f3d15e1 ("phy: qcom-qmp: new qmp phy driver for qcom-chipsets")
Signed-off-by: Johan Hovold <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Vinod Koul <[email protected]>
Switch to using the device-managed of_iomap helper to avoid leaking
memory on probe deferral and driver unbind.
Note that this helper checks for already reserved regions and may fail
if there are multiple devices claiming the same memory.
Fixes: e78f3d15e1 ("phy: qcom-qmp: new qmp phy driver for qcom-chipsets")
Signed-off-by: Johan Hovold <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Vinod Koul <[email protected]>
Switch to using the device-managed of_iomap helper to avoid leaking
memory on probe deferral and driver unbind.
Note that this helper checks for already reserved regions and may fail
if there are multiple devices claiming the same memory.
Fixes: e78f3d15e1 ("phy: qcom-qmp: new qmp phy driver for qcom-chipsets")
Signed-off-by: Johan Hovold <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Vinod Koul <[email protected]>
Switch to using the device-managed of_iomap helper to avoid leaking
memory on probe deferral and driver unbind.
Note that this helper checks for already reserved regions and may fail
if there are multiple devices claiming the same memory.
Fixes: e78f3d15e1 ("phy: qcom-qmp: new qmp phy driver for qcom-chipsets")
Signed-off-by: Johan Hovold <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Vinod Koul <[email protected]>
Make sure that the (otherwise) optional pcs_misc IO region has been
provided in case the configuration specifies a corresponding
initialisation table to avoid crashing with malformed device trees.
Note that the related debug message is now superfluous as the region is
only used when the configuration has a pcs_misc table.
Fixes: 421c9a0e97 ("phy: qcom: qmp: Add SDM845 PCIe QMP PHY support")
Signed-off-by: Johan Hovold <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Vinod Koul <[email protected]>
Drop the unused and incomplete runtime PM implementation, which was
only used by USB PHYs before splitting the QMP driver.
Note that the runtime PM was never disabled (and state restored) on
driver unbind.
This effectively reverts commit ac0d239936 ("phy: qcom-qmp: Add
support for runtime PM").
Signed-off-by: Johan Hovold <[email protected]>
Reviewed-by: Dmitry Baryshkov <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Vinod Koul <[email protected]>
Drop the unused and incomplete runtime PM implementation, which was
only used by USB PHYs before splitting the QMP driver.
Note that the runtime PM was never disabled (and state restored) on
driver unbind.
This effectively reverts commit ac0d239936 ("phy: qcom-qmp: Add
support for runtime PM").
Signed-off-by: Johan Hovold <[email protected]>
Reviewed-by: Dmitry Baryshkov <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Vinod Koul <[email protected]>
Drop the unused and incomplete runtime PM implementation, which was
only used by USB PHYs before splitting the QMP driver.
Note that the runtime PM was never disabled (and state restored) on
driver unbind.
This effectively reverts commit ac0d239936 ("phy: qcom-qmp: Add
support for runtime PM").
Signed-off-by: Johan Hovold <[email protected]>
Reviewed-by: Dmitry Baryshkov <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Vinod Koul <[email protected]>
Each of the CPSW5G ports in J7200 support additional modes like QSGMII.
Add a new compatible for J7200 to support the additional modes.
In TI's J7200, each of the CPSW5G ethernet interfaces can act as a
QSGMII or QSGMII-SUB port. The QSGMII interface is responsible for
performing auto-negotiation between the MAC and the PHY while the rest of
the interfaces are designated as QSGMII-SUB interfaces, indicating that
they will not be taking part in the auto-negotiation process.
To indicate the interface which will serve as the main QSGMII interface,
add a property "ti,qsgmii-main-ports", whose value indicates the
port number of the interface which shall serve as the main QSGMII
interface. The rest of the interfaces are then assigned QSGMII-SUB mode by
default. The property "ti,qsgmii-main-ports" is used to configure the
CTRLMMR_ENETx_CTRL register.
Depending on the device, it is possible for more than one QSGMII main port
to exist. Thus, the property "ti,qsgmii-main-ports" is defined as an array
of values in order to reuse the property for other devices.
Signed-off-by: Siddharth Vadapalli <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Vinod Koul <[email protected]>
In case of error, the function nvmem_cell_read() returns ERR_PTR()
and never returns NULL. The NULL test in the return value check
should be replaced with IS_ERR().
Fixes: 99d9ccd973 ("phy: usb: Add USB2.0 phy driver for Sunplus SP7021")
Signed-off-by: Wei Yongjun <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Vinod Koul <[email protected]>
The serdes driver contains also a mux to decide which interface type to
use. Currently the driver supports GMII/SGMII/QSGMII and partially RGMII.
As it doesn't support all the other RGMII interfaces like
RGMII_TXID/RXID/ID and it could run only at 1G.
Therefore extend this for all the other speeds(10/100) and also allow
the other interfaces.
Signed-off-by: Horatiu Vultur <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Vinod Koul <[email protected]>
The otg sync state patch reuses the ret variable, but fails to set it to
zero after use. This leads to a situation when the otg port is in
peripheral mode where the otg phy aborts halfway through setup. It also
fails to account for a failure to register the extcon notifier. Fix this
by using our own variable and skipping otg sync in case of failure.
Fixes: 8dc60f8da2 ("phy: rockchip-inno-usb2: Sync initial otg state")
Reported-by: Markus Reichl <[email protected]>
Reported-by: Michael Riesch <[email protected]>
Signed-off-by: Peter Geis <[email protected]>
Tested-by: Michael Riesch <[email protected]>
Tested-by: Markus Reichl <[email protected]>
Reviewed-by: Samuel Holland <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Vinod Koul <[email protected]>
RK3568 supports PCIe v3 using not Combphy like PCIe v2 on rk3566.
It use a dedicated PCIe-phy. Add support for this.
Initial support by Shawn Lin, modifications by Peter Geis and Frank
Wunderlich.
Add data-lanes property for splitting pcie-lanes across controllers.
The data-lanes is an array where x=0 means lane is disabled and x > 0
means controller x is assigned to phy lane.
Signed-off-by: Shawn Lin <[email protected]>
Suggested-by: Peter Geis <[email protected]>
Signed-off-by: Frank Wunderlich <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Vinod Koul <[email protected]>
When the platform was booted with the involved clocks enabled the
clk_set_rate() of the link and pixel clocks will perculate to the
children, which will fail to update because the PHY driver has just shut
down the PLL.
Postpone the clock rate updates until the PLL is back online to avoid
reconfiguring the clocks while the PLL is not ticking.
Fixes: f199223cb4 ("phy: qcom: Introduce new eDP PHY driver")
Signed-off-by: Bjorn Andersson <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Vinod Koul <[email protected]>
The pipe clock is defined in the "lane" node so there's no need to keep
adding a redundant lane-number suffix to the clock name.
Update driver to support the new binding where the pipe clock name has
been deprecated by instead requesting the clock by index.
Reviewed-by: Krzysztof Kozlowski <[email protected]>
Reviewed-by: Dmitry Baryshkov <[email protected]>
Signed-off-by: Johan Hovold <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Vinod Koul <[email protected]>
The lane reset is defined in the "lane" node so there's no need to keep
adding a redundant lane-number suffix to the reset name.
Update driver to support the new binding where the "lane" reset name has
been deprecated by instead requesting the reset by index.
Reviewed-by: Krzysztof Kozlowski <[email protected]>
Reviewed-by: Dmitry Baryshkov <[email protected]>
Signed-off-by: Johan Hovold <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Vinod Koul <[email protected]>
The pipe clock is defined in the "lane" node so there's no need to keep
adding a redundant lane-number suffix to the clock name.
Update driver to support the new binding where the pipe clock name has
been deprecated by instead requesting the clock by index.
Reviewed-by: Krzysztof Kozlowski <[email protected]>
Reviewed-by: Dmitry Baryshkov <[email protected]>
Signed-off-by: Johan Hovold <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Vinod Koul <[email protected]>
The pipe clock is defined in the "lane" node so there's no need to keep
adding a redundant lane-number suffix to the clock name.
Update driver to support the new binding where the pipe clock name has
been deprecated by instead requesting the clock by index.
Reviewed-by: Krzysztof Kozlowski <[email protected]>
Reviewed-by: Dmitry Baryshkov <[email protected]>
Signed-off-by: Johan Hovold <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Vinod Koul <[email protected]>
Johan Hovold